Seeding nucleofected hPSCs in 96-well plates using limited dilution
Yogendra Verma, Hanqin Li, Dirk Hockemeyer, Frank Soldner
Abstract
This protocol describes a standard procedure for seeding nucleofected human pluripotent stem cells in 96-well plates using limited dilution. This protocol follows nucleofection of hPSCs as described in detail in the collection "Nucleofection (Amaxa) and electroporation (Biorad) of hPSCs;" dx.doi.org/10.17504/protocols.io.b4qnqvve
General notes
- Throughout this protocol, the term hPSC is used to collectively refer to both hiPSCs and hESCs. All described procedures have been tested and work equally well for hiPSCs and hESCs.
Steps
For an editing with 10% efficiency, prepare two 96-well MEFs plates with a density at 2 million cells/plate at least 1 day ahead. Do not shake the plate after seeding MEFs. It generates swirls and causes cells to accumulate at the center. If editing efficiency is expected to be low, prepare more 96-well plates.
Calculate the number of cells needed. Cells should be seeded at a density that gives 20-30 colonies/plate. The density depends on cell survival post nucleofection, and varies between cell lines.
For every seeding density, make and label falcon tubes with 11 ml of hPSC medium + Rock inhibitor. Add the appropriate amount of cell solution to reach your desired cell concentration.
hPSC medium
| A | B |
|---|---|
| DMEM/F12 | 385 ml |
| Fetal Bovine Serum (FBS) | 75 ml |
| Knockout Serum Replacement | 25 ml |
| L-Glutamine (100X) | 5 ml |
| Penicillin & Streptomycin (100X) | 5 ml |
| MEM Non-Essential Amino Acids (100X) | 5 ml |
| 2-Mercaptoethanol (10,000X) | 50 µl |
| Heat Stable Recombinant Human FGF2 (25ug/ml)* | 80 µl |
*While we prefer Heat Stable Recombinant Human FGF2, we also have used regular FGF2. Final volume: 500ml
L-Glutamine (100X)
| A | B |
|---|---|
| L-Glutamine, powder | 14.6 g |
| MilliQ H2O | 500 ml |
2-Mercaptoethanol (10,000X)
| A | B |
|---|---|
| 2-Mercaptoethanol | 0.78 ml |
| MilliQ H2O | 9.22 ml |
Heat Stable Recombinant Human FGF2 (25µg/ml)
| A | B |
|---|---|
| Heat Stable Recombinant Human FGF2 | 500 µg |
| 0.1% BSA | 20 ml |
Final volume: 20ml
Y-27632 (1,000X)
| A | B |
|---|---|
| Y-27632 | 5 mg |
| DMSO | 1.56 ml |
hPSC medium + Rock inhibitor
| A | B |
|---|---|
| hPSCs medium | 500 ml |
| Y-27632 (1,000X) | 500 µl |
Final volume: 500ml
Take out 96-well MEF plates, carefully label them with their cell seeding number.
Aspirate feeder medium from the plates, then add 100 µl/well using a multichannel pipette and 200 µl filter tips. Use a sterile reagent reservoir for medium.
Additionally, prepare one well of a 6-well plate for each seeding density on your 96-well format. Seed the same number of cells that were seeded to the 96-well plate to this well, e.g. 1,000 cells. These will be analyzed in parallel to track the approximate number of expected colonies/clones from the 96-well plates.
Seed the rest of cells to another well of a 6-well plate. This will become the bulk sample for estimating the editing efficiency. Change medium daily starting from day 3 for this well and prepare crude cell lysis once it reaches a good confluency.
Crude lysis buffer (2x)
| A | B |
|---|---|
| KCl | 100mM |
| MgCl2 | 4mM |
| NP-40 | 0.9% |
| Tween-20 | 0.9% |
| Tris | 20mM |
| Proteinase K (add before use) | 500µg/ml |
pH: 8
Change medium for your 96-well plates by using a multi-channel pipet and aspirator every three days. Reduce it to once every two days once the colonies in your plates grow bigger, or during the second week post-nucleofection.
Keep cells in culture for 10-14 days. Proceed with plate duplication if the well in the 6-well plate (originally seeded with 1,000 cells) shows 20-50 colonies.
